Discovering Plumbing Basics is Essential For Installing a Bathtub
Discovering Plumbing Basics is Essential For Installing a Bathtub
Blog Article
This article which follows pertaining to Installing A Bathtub is fairly entertaining. Check it out yourself and figure out what you think of it.
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
Mounting a bath tub isn't exactly rocket science, but it does need solid plumbing, woodworking, as well as occasionally, tiling skills. Changing an old bath tub with a brand-new one is additionally a moderately tough job. If the old tub is readily available, the task can move speedily; if you need to open a wall surface to eliminate the old bathtub and also place the brand-new tub, the job is much harder. In either case, the task is within a house handyman's abilities, although you will need an assistant to leave the old tub as well as set in the new one. See to it you have qualified yourself for the task as well as are comfortable trying it. Rather than working with a contractor to take control of a halfway-completed task, it is far better to consider utilizing one before you begin. Possibilities are you may require an expert plumber to make tube links.
This write-up will aid you mount a new tub in your bathroom if you have currently bought a new bathtub as well as don't need to transform the setup of your previous water system pipes.
Your devices and product checklist should comprise the following:
Removing Old Touches
If you require to change old taps with new ones as a part of your setup, after that the first thing you should do is disconnect the water system. After doing so, turn on the faucets to drain any type of water remaining in the system. The procedure of eliminating the existing faucets can be rather troublesome because of the limited accessibility that is typically the instance.
Use a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipelines to the taps. Have a fabric ready for the continuing to be water that will certainly come from the pipes. When the supply pipes have been removed, make use of the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single taps from transforming during this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any type of old sealing compound.
Prior to moving on to fit the brand-new faucets, compare the pipe connections on the old taps to the new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the new faucets to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will need a plastic adapter to stop damage to the thread. One end of the adapter fits on the plastic tail of the faucet and also the various other end gives a link to the existing supply pipes.
If you require to fit a monobloc, after that you will certainly call for minimizing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, position the faucet in the installing hole in the bath/basin making sure that the washing machines are in area in between the tap and the sink. Safeguard the faucet in place with the maker given backnut. As soon as the tap is safely in place, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with typical tap adapters. The previous type ought to be attached to the tap finishes first, tightening up just by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have been connected.
Setting up the Bath tub
Using both wooden boards under its feet, place the bathtub in the called for setting. The wood boards are useful in equally spreading the weight of the tub over the area of the boards instead of focusing all the weight onto 4 little points.
The following goal is to ensure that the tub is leveled all round. This can be accomplished by examining the spirit level and readjusting the feet on the bathtub up until the level reviews degree.
To set up faucets, fit all-time low of the outermost adaptable faucet connector to the ideal supply pipeline by making a compression sign up with; then do the very same for the various other faucet.
Switch on the supply of water and also inspect all joints as well as new pipework for leaks as well as tighten them if necessary. Fill the bath tub and likewise examine the overflow outlet and the normal electrical outlet for leakages.
Lastly, deal with the bathroom paneling as defined in the supplier's instruction manual. Tiling and also securing around the tub must wait until the bath tub has been utilized at least when as this will settle it into its last placement.
Planning for the Installation
To start with, the supporting structure provided with the bathroom needs to be fitted (if required) according to the producer's instructions. Next off, fit the taps or mixer to the bathtub. When fitting the faucet block, it is essential to see to it that if the tap includes a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is additionally practical to fit a supporting plate under the taps system to prevent strain on the bath tub.
Fit the versatile faucet ports to the bottom of the two taps utilizing 2 nuts and olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet through the hole in the bath. Use the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Ensure you make use of every one of the provided washers.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath should currently prepare to be suited its last position.
Tiling Around the Bath tub
In the area where the bath meets the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to crack a stiff seal, triggering the water to pass through the wall between the bathroom and also the tiling, bring about issues with dampness as well as possible leakages to the ceiling below.
You can choose from a variety of coloured sealers to blend in your fixtures and also installations. They are offered in tubes as well as cartridges, and can securing gaps as much as a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with twists of soaked newspaper or soft rope. Bear in mind to always fill the bathtub with water before securing, to enable the movement experienced when the bathtub is in use. The sealant can crack fairly early if you do not take into consideration this motion prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are additionally quickly readily available on the market. It is suggested to fit the ceramic tiles making use of water-resistant or water-proof adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm very fascinated with How to Install a Bathtub Yourself and I hope you appreciated our blog post. Feel free to take a moment to share this blog posting if you liked it. Thanks so much for your time invested reading it.
Plumbing SOS? Reach out! Report this page